Cubot GT90 [Android 4.2.2] Stock Firmware, Flash File Download

This Cubot GT90 [Android 4.2.2] Firmware, Stock ROM can be used with any service tools capable of Flashing Stock ROM, flash file (MTK Backup) on Cubot Android devices.

Stock firmware are mostly needed to either upgrade your Cubot GT90 [Android 4.2.2] or flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Cubot GT90 [Android 4.2.2] Stock ROM, flash file which can be used to flash factory OS back to your Cubot GT90 [Android 4.2.2].

How to Download Stock Firmware and Flash Cubot GT90 [Android 4.2.2] with this Stock ROM, Flash File

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Cubot GT90 [Android 4.2.2] stock firmware, Flash File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Cubot GT90 [Android 4.2.2] Stock ROM, flash file and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Cubot GT90 [Android 4.2.2] stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Cubot GT90 [Android 4.2.2] Stock ROM you downloaded. From the list, Mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Cubot GT90 [Android 4.2.2] or remove battery from it and re-insert the battery again. Connect your Cubot GT90 [Android 4.2.2] Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Cubot GT90 [Android 4.2.2] to its factory defaults.
NOTE: if you encounter any errors while flashing your Cubot GT90 [Android 4.2.2] using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Cubot android devices, see here: How to Flash Cubot Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete VCOM Driver for MTK Android Devices On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock ROM, flash file Download

Video Tutorial: How to Flash All MTK Android Devices Including Cubot GT90 [Android 4.2.2]

Source: firmwarefile

Opsson IVO 6688 Stock Firmware, Stock ROM Download

This Opsson IVO 6688 Firmware, Stock ROM file can be used with any service tools capable of Flashing Stock ROM file on Opsson Android devices.

Stock firmware are mostly needed to either upgrade your Opsson IVO 6688, downgrade it or, to simply flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Opsson IVO 6688, Stock ROM file which can be used to flash factory OS back to your Opsson IVO 6688.

How to Download Stock Firmware and Flash Opsson IVO 6688 with the Stock ROM

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Opsson IVO 6688 firmware, Stock ROM File from here. Or, Opsson IVO 6688 firmware, Stock ROM File from here [2nd Variant]

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Opsson IVO 6688 Stock ROM and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Opsson IVO 6688 stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Opsson IVO 6688 stock ROM you downloaded. From the list, mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Opsson IVO 6688 or remove battery from it and re-insert the battery again. Connect your Opsson IVO 6688 Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Opsson IVO 6688 to its factory defaults.
NOTE: if you encounter any errors while flashing your Opsson IVO 6688 using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Opsson android devices, see here: How to Flash Opsson Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete MTK Android Drivers [VCOM Drivers] Driver On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock Firmware, PAC File Download

Video Tutorial: How to Flash All MTK Android Devices Including Opsson IVO 6688

Cubot GT89 [Android 4.2.1] Stock Firmware, Flash File Download

This Cubot GT89 [Android 4.2.1] Firmware, Stock ROM can be used with any service tools capable of Flashing Stock ROM, flash file (MTK Backup) on Cubot Android devices.

Stock firmware are mostly needed to either upgrade your Cubot GT89 [Android 4.2.1] or flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Cubot GT89 [Android 4.2.1] Stock ROM, flash file which can be used to flash factory OS back to your Cubot GT89 [Android 4.2.1].

How to Download Stock Firmware and Flash Cubot GT89 [Android 4.2.1] with this Stock ROM, Flash File

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Cubot GT89 [Android 4.2.1] stock firmware, Flash File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Cubot GT89 [Android 4.2.1] Stock ROM, flash file and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Cubot GT89 [Android 4.2.1] stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Cubot GT89 [Android 4.2.1] Stock ROM you downloaded. From the list, Mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Cubot GT89 [Android 4.2.1] or remove battery from it and re-insert the battery again. Connect your Cubot GT89 [Android 4.2.1] Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Cubot GT89 [Android 4.2.1] to its factory defaults.
NOTE: if you encounter any errors while flashing your Cubot GT89 [Android 4.2.1] using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Cubot android devices, see here: How to Flash Cubot Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete VCOM Driver for MTK Android Devices On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock ROM, flash file Download

Video Tutorial: How to Flash All MTK Android Devices Including Cubot GT89 [Android 4.2.1]

Source: firmwarefile

Opsson S1 V13 Stock Firmware, Stock ROM Download

This Opsson S1 V13 Firmware, Stock ROM file can be used with any service tools capable of Flashing Stock ROM file on Opsson Android devices.

Stock firmware are mostly needed to either upgrade your Opsson S1 V13, downgrade it or, to simply flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Opsson S1 V13, Stock ROM file which can be used to flash factory OS back to your Opsson S1 V13.

How to Download Stock Firmware and Flash Opsson S1 V13 with the Stock ROM

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Opsson S1 V13 firmware, Stock ROM File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Opsson S1 V13 Stock ROM and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Opsson S1 V13 stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Opsson S1 V13 stock ROM you downloaded. From the list, mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Opsson S1 V13 or remove battery from it and re-insert the battery again. Connect your Opsson S1 V13 Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Opsson S1 V13 to its factory defaults.
NOTE: if you encounter any errors while flashing your Opsson S1 V13 using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Opsson android devices, see here: How to Flash Opsson Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete MTK Android Drivers [VCOM Drivers] Driver On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock Firmware, PAC File Download

Video Tutorial: How to Flash All MTK Android Devices Including Opsson S1 V13

Cubot GT99 [Android 4.2.1] Stock Firmware, Flash File Download

This Cubot GT99 [Android 4.2.1] Firmware, Stock ROM can be used with any service tools capable of Flashing Stock ROM, flash file (MTK Backup) on Cubot Android devices.

Stock firmware are mostly needed to either upgrade your Cubot GT99 [Android 4.2.1] or flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Cubot GT99 [Android 4.2.1] Stock ROM, flash file which can be used to flash factory OS back to your Cubot GT99 [Android 4.2.1].

How to Download Stock Firmware and Flash Cubot GT99 [Android 4.2.1] with this Stock ROM, Flash File

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Cubot GT99 [Android 4.2.1] stock firmware, Flash File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Cubot GT99 [Android 4.2.1] Stock ROM, flash file and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Cubot GT99 [Android 4.2.1] stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Cubot GT99 [Android 4.2.1] Stock ROM you downloaded. From the list, Mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Cubot GT99 [Android 4.2.1] or remove battery from it and re-insert the battery again. Connect your Cubot GT99 [Android 4.2.1] Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Cubot GT99 [Android 4.2.1] to its factory defaults.
NOTE: if you encounter any errors while flashing your Cubot GT99 [Android 4.2.1] using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Cubot android devices, see here: How to Flash Cubot Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete VCOM Driver for MTK Android Devices On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock ROM, flash file Download

Video Tutorial: How to Flash All MTK Android Devices Including Cubot GT99 [Android 4.2.1]

Source: firmwarefile

Opsson Q7 Stock Firmware, Stock ROM Download

This Opsson Q7 Firmware, Stock ROM file can be used with any service tools capable of Flashing Stock ROM file on Opsson Android devices.

Stock firmware are mostly needed to either upgrade your Opsson Q7, downgrade it or, to simply flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Opsson Q7, Stock ROM file which can be used to flash factory OS back to your Opsson Q7.

How to Download Stock Firmware and Flash Opsson Q7 with the Stock ROM

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Opsson Q7 firmware, Stock ROM File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Opsson Q7 Stock ROM and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Opsson Q7 stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Opsson Q7 stock ROM you downloaded. From the list, mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Opsson Q7 or remove battery from it and re-insert the battery again. Connect your Opsson Q7 Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Opsson Q7 to its factory defaults.
NOTE: if you encounter any errors while flashing your Opsson Q7 using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Opsson android devices, see here: How to Flash Opsson Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete MTK Android Drivers [VCOM Drivers] Driver On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock Firmware, PAC File Download

Video Tutorial: How to Flash All MTK Android Devices Including Opsson Q7

Cubot M6589 [Android 4.2.1] Stock Firmware, Flash File Download

This Cubot M6589 [Android 4.2.1] Firmware, Stock ROM can be used with any service tools capable of Flashing Stock ROM, flash file (MTK Backup) on Cubot Android devices.

Stock firmware are mostly needed to either upgrade your Cubot M6589 [Android 4.2.1] or flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Cubot M6589 [Android 4.2.1] Stock ROM, flash file which can be used to flash factory OS back to your Cubot M6589 [Android 4.2.1].

How to Download Stock Firmware and Flash Cubot M6589 [Android 4.2.1] with this Stock ROM, Flash File

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Cubot M6589 [Android 4.2.1] stock firmware, Flash File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Cubot M6589 [Android 4.2.1] Stock ROM, flash file and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Cubot M6589 [Android 4.2.1] stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Cubot M6589 [Android 4.2.1] Stock ROM you downloaded. From the list, Mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Cubot M6589 [Android 4.2.1] or remove battery from it and re-insert the battery again. Connect your Cubot M6589 [Android 4.2.1] Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Cubot M6589 [Android 4.2.1] to its factory defaults.
NOTE: if you encounter any errors while flashing your Cubot M6589 [Android 4.2.1] using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Cubot android devices, see here: How to Flash Cubot Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete VCOM Driver for MTK Android Devices On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock ROM, flash file Download

Video Tutorial: How to Flash All MTK Android Devices Including Cubot M6589 [Android 4.2.1]

Source: firmwarefile

Opsson Q5 Stock Firmware, Stock ROM Download

This Opsson Q5 Firmware, Stock ROM file can be used with any service tools capable of Flashing Stock ROM file on Opsson Android devices.

Stock firmware are mostly needed to either upgrade your Opsson Q5, downgrade it or, to simply flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Opsson Q5, Stock ROM file which can be used to flash factory OS back to your Opsson Q5.

How to Download Stock Firmware and Flash Opsson Q5 with the Stock ROM

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Opsson Q5 firmware, Stock ROM File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Opsson Q5 Stock ROM and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Opsson Q5 stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Opsson Q5 stock ROM you downloaded. From the list, mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Opsson Q5 or remove battery from it and re-insert the battery again. Connect your Opsson Q5 Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Opsson Q5 to its factory defaults.
NOTE: if you encounter any errors while flashing your Opsson Q5 using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Opsson android devices, see here: How to Flash Opsson Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete MTK Android Drivers [VCOM Drivers] Driver On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock Firmware, PAC File Download

Video Tutorial: How to Flash All MTK Android Devices Including Opsson Q5

Cubot ONE [Android 4.2.1] Stock Firmware, Flash File Download

This Cubot ONE [Android 4.2.1] Firmware, Stock ROM can be used with any service tools capable of Flashing Stock ROM, flash file (MTK Backup) on Cubot Android devices.

Stock firmware are mostly needed to either upgrade your Cubot ONE [Android 4.2.1] or flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Cubot ONE [Android 4.2.1] Stock ROM, flash file which can be used to flash factory OS back to your Cubot ONE [Android 4.2.1].

How to Download Stock Firmware and Flash Cubot ONE [Android 4.2.1] with this Stock ROM, Flash File

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Cubot ONE [Android 4.2.1] stock firmware, Flash File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Cubot ONE [Android 4.2.1] Stock ROM, flash file and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Cubot ONE [Android 4.2.1] stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Cubot ONE [Android 4.2.1] Stock ROM you downloaded. From the list, Mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Cubot ONE [Android 4.2.1] or remove battery from it and re-insert the battery again. Connect your Cubot ONE [Android 4.2.1] Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Cubot ONE [Android 4.2.1] to its factory defaults.
NOTE: if you encounter any errors while flashing your Cubot ONE [Android 4.2.1] using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Cubot android devices, see here: How to Flash Cubot Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete VCOM Driver for MTK Android Devices On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock ROM, flash file Download

Video Tutorial: How to Flash All MTK Android Devices Including Cubot ONE [Android 4.2.1]

Source: firmwarefile

Opsson Q1 Stock Firmware, Stock ROM Download

This Opsson Q1 Firmware, Stock ROM file can be used with any service tools capable of Flashing Stock ROM file on Opsson Android devices.

Stock firmware are mostly needed to either upgrade your Opsson Q1, downgrade it or, to simply flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Opsson Q1, Stock ROM file which can be used to flash factory OS back to your Opsson Q1.

How to Download Stock Firmware and Flash Opsson Q1 with the Stock ROM

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Opsson Q1 firmware, Stock ROM File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Opsson Q1 Stock ROM and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Opsson Q1 stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Opsson Q1 stock ROM you downloaded. From the list, mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Opsson Q1 or remove battery from it and re-insert the battery again. Connect your Opsson Q1 Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Opsson Q1 to its factory defaults.
NOTE: if you encounter any errors while flashing your Opsson Q1 using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Opsson android devices, see here: How to Flash Opsson Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete MTK Android Drivers [VCOM Drivers] Driver On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock Firmware, PAC File Download

Video Tutorial: How to Flash All MTK Android Devices Including Opsson Q1

Cubot P5 [Android 4.2.2] Stock Firmware, Flash File Download

This Cubot P5 [Android 4.2.2] Firmware, Stock ROM can be used with any service tools capable of Flashing Stock ROM, flash file (MTK Backup) on Cubot Android devices.

Stock firmware are mostly needed to either upgrade your Cubot P5 [Android 4.2.2] or flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Cubot P5 [Android 4.2.2] Stock ROM, flash file which can be used to flash factory OS back to your Cubot P5 [Android 4.2.2].

How to Download Stock Firmware and Flash Cubot P5 [Android 4.2.2] with this Stock ROM, Flash File

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Cubot P5 [Android 4.2.2] stock firmware, Flash File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Cubot P5 [Android 4.2.2] Stock ROM, flash file and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Cubot P5 [Android 4.2.2] stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Cubot P5 [Android 4.2.2] Stock ROM you downloaded. From the list, Mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Cubot P5 [Android 4.2.2] or remove battery from it and re-insert the battery again. Connect your Cubot P5 [Android 4.2.2] Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Cubot P5 [Android 4.2.2] to its factory defaults.
NOTE: if you encounter any errors while flashing your Cubot P5 [Android 4.2.2] using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Cubot android devices, see here: How to Flash Cubot Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete VCOM Driver for MTK Android Devices On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock ROM, flash file Download

Video Tutorial: How to Flash All MTK Android Devices Including Cubot P5 [Android 4.2.2]

Source: firmwarefile

Opsson i806 Stock Firmware, Stock ROM Download

This Opsson i806 Firmware, Stock ROM file can be used with any service tools capable of Flashing Stock ROM file on Opsson Android devices.

Stock firmware are mostly needed to either upgrade your Opsson i806, downgrade it or, to simply flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Opsson i806, Stock ROM file which can be used to flash factory OS back to your Opsson i806.

How to Download Stock Firmware and Flash Opsson i806 with the Stock ROM

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Opsson i806 firmware, Stock ROM File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Opsson i806 Stock ROM and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Opsson i806 stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Opsson i806 stock ROM you downloaded. From the list, mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Opsson i806 or remove battery from it and re-insert the battery again. Connect your Opsson i806 Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Opsson i806 to its factory defaults.
NOTE: if you encounter any errors while flashing your Opsson i806 using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Opsson android devices, see here: How to Flash Opsson Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete MTK Android Drivers [VCOM Drivers] Driver On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock Firmware, PAC File Download

Video Tutorial: How to Flash All MTK Android Devices Including Opsson i806

Cubot P6 [Android 4.2.2] Stock Firmware, Flash File Download

This Cubot P6 [Android 4.2.2] Firmware, Stock ROM can be used with any service tools capable of Flashing Stock ROM, flash file (MTK Backup) on Cubot Android devices.

Stock firmware are mostly needed to either upgrade your Cubot P6 [Android 4.2.2] or flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Cubot P6 [Android 4.2.2] Stock ROM, flash file which can be used to flash factory OS back to your Cubot P6 [Android 4.2.2].

How to Download Stock Firmware and Flash Cubot P6 [Android 4.2.2] with this Stock ROM, Flash File

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Cubot P6 [Android 4.2.2] stock firmware, Flash File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Cubot P6 [Android 4.2.2] Stock ROM, flash file and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Cubot P6 [Android 4.2.2] stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Cubot P6 [Android 4.2.2] Stock ROM you downloaded. From the list, Mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Cubot P6 [Android 4.2.2] or remove battery from it and re-insert the battery again. Connect your Cubot P6 [Android 4.2.2] Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Cubot P6 [Android 4.2.2] to its factory defaults.
NOTE: if you encounter any errors while flashing your Cubot P6 [Android 4.2.2] using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Cubot android devices, see here: How to Flash Cubot Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete VCOM Driver for MTK Android Devices On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock ROM, flash file Download

Video Tutorial: How to Flash All MTK Android Devices Including Cubot P6 [Android 4.2.2]

Source: firmwarefile

Opsson IVO 6677 Stock Firmware, Stock ROM Download

This Opsson IVO 6677 Firmware, Stock ROM file can be used with any service tools capable of Flashing Stock ROM file on Opsson Android devices.

Stock firmware are mostly needed to either upgrade your Opsson IVO 6677, downgrade it or, to simply flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Opsson IVO 6677, Stock ROM file which can be used to flash factory OS back to your Opsson IVO 6677.

How to Download Stock Firmware and Flash Opsson IVO 6677 with the Stock ROM

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Opsson IVO 6677 firmware, Stock ROM File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Opsson IVO 6677 Stock ROM and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Opsson IVO 6677 stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Opsson IVO 6677 stock ROM you downloaded. From the list, mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Opsson IVO 6677 or remove battery from it and re-insert the battery again. Connect your Opsson IVO 6677 Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Opsson IVO 6677 to its factory defaults.
NOTE: if you encounter any errors while flashing your Opsson IVO 6677 using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Opsson android devices, see here: How to Flash Opsson Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete MTK Android Drivers [VCOM Drivers] Driver On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock Firmware, PAC File Download

Video Tutorial: How to Flash All MTK Android Devices Including Opsson IVO 6677

Cubot P9 Stock Firmware, Stock ROM Download: All Versions

These Cubot P9 Firmware, Stock ROM file can be used with any service tools capable of Flashing Stock ROM file on Cubot Android devices.

Stock firmware are mostly needed to either upgrade your Cubot P9 or flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download links for all the complete Cubot P9, Stock ROM files which can be used to flash factory OS back to your Cubot P9.

How to Download Stock Firmware and Flash Cubot P9 with these Stock Firmwares/ROM

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download the appropriate variant of Cubot P9 Firmware from the list below:
Download 1st Variant -(P9 (140213) Android 4.2.2)
Download 2nd Variant -(P9 V1.5-20131016)
Download 2nd Variant -(P9 V1.12-20140828)

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Cubot P9 Stock ROM and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Cubot P9 stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Cubot P9 stock ROM you downloaded. From the list, mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Cubot P9 or remove battery from it and re-insert the battery again. Connect your Cubot P9 Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Cubot P9 to its factory defaults.
NOTE: if you encounter any errors while flashing your Cubot P9 using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Cubot android devices, see here: How to Flash Cubot Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete VCOM Driver for MTK Android Devices On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All Cubot Android Stock Firmware Stock ROM File Download
• All iTel Android Stock ROM Stock ROM File Download

Video Tutorial: How to Flash All MTK Android Devices Including Cubot P9

Opsson IVO 6655 Stock Firmware, Stock ROM Download

This Opsson IVO 6655 Firmware, Stock ROM file can be used with any service tools capable of Flashing Stock ROM file on Opsson Android devices.

Stock firmware are mostly needed to either upgrade your Opsson IVO 6655, downgrade it or, to simply flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Opsson IVO 6655, Stock ROM file which can be used to flash factory OS back to your Opsson IVO 6655.

How to Download Stock Firmware and Flash Opsson IVO 6655 with the Stock ROM

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Opsson IVO 6655 firmware, Stock ROM File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Opsson IVO 6655 Stock ROM and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Opsson IVO 6655 stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Opsson IVO 6655 stock ROM you downloaded. From the list, mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Opsson IVO 6655 or remove battery from it and re-insert the battery again. Connect your Opsson IVO 6655 Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Opsson IVO 6655 to its factory defaults.
NOTE: if you encounter any errors while flashing your Opsson IVO 6655 using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Opsson android devices, see here: How to Flash Opsson Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete MTK Android Drivers [VCOM Drivers] Driver On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock Firmware, PAC File Download

Video Tutorial: How to Flash All MTK Android Devices Including Opsson IVO 6655

Cubot S108 [Android 4.4.2] Stock Firmware, Flash File Download

This Cubot S108 [Android 4.4.2] Firmware, Stock ROM can be used with any service tools capable of Flashing Stock ROM, flash file (MTK Backup) on Cubot Android devices.

Stock firmware are mostly needed to either upgrade your Cubot S108 [Android 4.4.2] or flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Cubot S108 [Android 4.4.2] Stock ROM, flash file which can be used to flash factory OS back to your Cubot S108 [Android 4.4.2].

How to Download Stock Firmware and Flash Cubot S108 [Android 4.4.2] with this Stock ROM, Flash File

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Cubot S108 [Android 4.4.2] stock firmware, Flash File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Cubot S108 [Android 4.4.2] Stock ROM, flash file and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Cubot S108 [Android 4.4.2] stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Cubot S108 [Android 4.4.2] Stock ROM you downloaded. From the list, Mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Cubot S108 [Android 4.4.2] or remove battery from it and re-insert the battery again. Connect your Cubot S108 [Android 4.4.2] Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Cubot S108 [Android 4.4.2] to its factory defaults.
NOTE: if you encounter any errors while flashing your Cubot S108 [Android 4.4.2] using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Cubot android devices, see here: How to Flash Cubot Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete VCOM Driver for MTK Android Devices On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock ROM, flash file Download

Video Tutorial: How to Flash All MTK Android Devices Including Cubot S108 [Android 4.4.2]

Source: firmwarefile

Opsson 6611 Stock Firmware, Stock ROM Download

This Opsson 6611 Firmware, Stock ROM file can be used with any service tools capable of Flashing Stock ROM file on Opsson Android devices.

Stock firmware are mostly needed to either upgrade your Opsson 6611, downgrade it or, to simply flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Opsson 6611, Stock ROM file which can be used to flash factory OS back to your Opsson 6611.

How to Download Stock Firmware and Flash Opsson 6611 with the Stock ROM

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Opsson 6611 firmware, Stock ROM File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Opsson 6611 Stock ROM and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Opsson 6611 stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Opsson 6611 stock ROM you downloaded. From the list, mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Opsson 6611 or remove battery from it and re-insert the battery again. Connect your Opsson 6611 Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Opsson 6611 to its factory defaults.
NOTE: if you encounter any errors while flashing your Opsson 6611 using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Opsson android devices, see here: How to Flash Opsson Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete MTK Android Drivers [VCOM Drivers] Driver On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock Firmware, PAC File Download

Video Tutorial: How to Flash All MTK Android Devices Including Opsson 6611

Cubot S208 V12 Stock Firmware, Flash File Download

This Cubot S208 V12 Firmware, Stock ROM can be used with any service tools capable of Flashing Stock ROM, flash file (MTK Backup) on Cubot Android devices.

Stock firmware are mostly needed to either upgrade your Cubot S208 V12 or flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Cubot S208 V12 Stock ROM, flash file which can be used to flash factory OS back to your Cubot S208 V12.

How to Download Stock Firmware and Flash Cubot S208 V12 with this Stock ROM, Flash File

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Cubot S208 V12 stock firmware, Flash File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Cubot S208 V12 Stock ROM, flash file and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Cubot S208 V12 stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Cubot S208 V12 Stock ROM you downloaded. From the list, Mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Cubot S208 V12 or remove battery from it and re-insert the battery again. Connect your Cubot S208 V12 Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Cubot S208 V12 to its factory defaults.
NOTE: if you encounter any errors while flashing your Cubot S208 V12 using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Cubot android devices, see here: How to Flash Cubot Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete VCOM Driver for MTK Android Devices On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock ROM, flash file Download

Video Tutorial: How to Flash All MTK Android Devices Including Cubot S208 V12

Source: firmwarefile

Opsson IVO 6600 Stock Firmware, Stock ROM Download

This Opsson IVO 6600 Firmware, Stock ROM file can be used with any service tools capable of Flashing Stock ROM file on Opsson Android devices.

Stock firmware are mostly needed to either upgrade your Opsson IVO 6600, downgrade it or, to simply flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Opsson IVO 6600, Stock ROM file which can be used to flash factory OS back to your Opsson IVO 6600.

How to Download Stock Firmware and Flash Opsson IVO 6600 with the Stock ROM

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Opsson IVO 6600 firmware, Stock ROM File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Opsson IVO 6600 Stock ROM and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Opsson IVO 6600 stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Opsson IVO 6600 stock ROM you downloaded. From the list, mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Opsson IVO 6600 or remove battery from it and re-insert the battery again. Connect your Opsson IVO 6600 Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Opsson IVO 6600 to its factory defaults.
NOTE: if you encounter any errors while flashing your Opsson IVO 6600 using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Opsson android devices, see here: How to Flash Opsson Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete MTK Android Drivers [VCOM Drivers] Driver On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock Firmware, PAC File Download

Video Tutorial: How to Flash All MTK Android Devices Including Opsson IVO 6600

Cubot S222 V6 [Android 4.4.2] Stock Firmware, Flash File Download

This Cubot S222 V6 [Android 4.4.2] CQ 4139C D1BOM V0.0.2 20140807 Firmware, Stock ROM can be used with any service tools capable of Flashing Stock ROM, flash file (MTK Backup) on Cubot Android devices.

Stock firmware are mostly needed to either upgrade your Cubot S222 V6 [Android 4.4.2] or flash the phone to correct certain software issues or malfunctions on the phone. Here on this page I have contained the download link for the complete Cubot S222 V6 [Android 4.4.2] Stock ROM, flash file which can be used to flash factory OS back to your Cubot S222 V6 [Android 4.4.2].

How to Download Stock Firmware and Flash Cubot S222 V6 [Android 4.4.2] with this Stock ROM, Flash File

1. Download SP Flash Tool from here and install it on your PC. If you don't have MTK Android drivers installed on your PC yet, you must install it too. Download VCOM Drivers here

2. Download your Cubot S222 V6 [Android 4.4.2] stock firmware, Flash File from here.

3. Open the SP Flash Tool you downloaded from the link above. It is compressed in a zip file, simply extract it onto a folder on your PC, open the folder to locate flash_tool.exe application and then; double-click it to lunch the program.

4. Go to the folder where you downloaded the Cubot S222 V6 [Android 4.4.2] Stock ROM, flash file and open it. It is compressed in a ZIP File, simply decompress/unzip it onto a folder on your PC.

5. On SP Flash Tool, select Scatter Loading. A window should open. Using the browse button, navigate to the folder where you unzipped the Cubot S222 V6 [Android 4.4.2] stock ROM and then select "MTXXXX-ANDROID-SCATTER", from there. Remember: "xxxx" refers to the MTK version of your phone.

6. Once selected, SP Flash Tool will load all the partitions in the Cubot S222 V6 [Android 4.4.2] Stock ROM you downloaded. From the list, Mark all the partitions EXCEPT these three (3): Preloader, UserData and CACHE.

7. Now, select Download on SP Flash Tool.

8. Put off your Cubot S222 V6 [Android 4.4.2] or remove battery from it and re-insert the battery again. Connect your Cubot S222 V6 [Android 4.4.2] Mobile Phone to the PC and then tap the Power button once.

9. For few seconds, your Windows PC will install the necessary drivers for the flashing operation and then, the flashing operation will commence promptly.

10. When the flashing operation completes, SP Flash Tool will display a green PASS circle. You may then disconnect your phone from the PC.
CONGRATULATIONS! You have successfully flashed your Cubot S222 V6 [Android 4.4.2] to its factory defaults.
NOTE: if you encounter any errors while flashing your Cubot S222 V6 [Android 4.4.2] using SP Flash Tools, see here: Solutions to All SP Flash Tools Errors: Practical Guides

For Graphical Illustrations on how to flash Cubot android devices, see here: How to Flash Cubot Android Device: Step by Step with Pictures

Also Read:

• How to Install Complete VCOM Driver for MTK Android Devices On your PC
• How to Flash MTK Android Devices Using Miracle Box
• All iTel Android Stock ROM, flash file Download

Video Tutorial: How to Flash All MTK Android Devices Including Cubot S222 V6 [Android 4.4.2]

Source: firmwarefile